20xBeehive electric heater 12V 10W and 1xTemp controller, heating hive Full set. Beehive electric heater 12V 10W - 20 pcs (Made in Ukraine). Temp controller (Made in Russia) - 1 pcs.Beehive 12V/ 10W, size 100X100mm. Heater beehive is an environmentally friendly product. Through the use of the cermet of the heating element are not allocated any harmful substances or electromagnetic radiation. Many beekeepers have long appreciated the benefits of the heater to the hive. Electric heater allows increasing the air temperature inside the hive. And even though the temperature rises not much, but it's enough for a significant stimulation of the queen bee to lay eggs. In this simple way, beekeepers have to early spring bribe receive strong bee colonies, or the opportunity to strains. Voltage 12V AC or DC. 10W rated power of the appliance.
Product weight not more than 0,15kg. Rated temperature of the body surface is not more than 40 ° C. Warming up to a nominal temperature of at least 10 minutes. Heater hive is designed for continuous operation.
The electrical resistance of the device should be serviceable in the range of 13 to 16 ohms. Note: When using this product, maybe a serial connection of electric heaters beehive (by type of connection lights Christmas tree garlands). To power from household 110V network in this connection it is necessary to connect at least 10 electric heaters.
To power on the home network 220V in this connection it is necessary to connect at least 20 electric heaters. Thermostat for controlling the operation of heating devices, including electric heaters beehive. Main technical data: S upply voltage AC 220 V, 50-60 Hz. Temperature adjustment range from -5 ° C to + 40 ° C. Ambient temperature from -40 ° C to + 60 ° C.
The output control signal - AC voltage 220V. The maximum output current of 16A. The maximum ability to connect to the thermostat 3 kW load. Dimensions (mm) in multiples of 110 × 80 × 75, but the thermostat 90 × 50 × 70. The materials and components used in the manufacture of the goods: in the kit includes a temperature regulator ART 18-16N sensor KTY-81-110 (on a wire of 1.5 m), product data with options for connecting load circuits for Russian Language.The thermostat consists of a body, on the front of which are the scale of temperature control, temperature control knob and indicator LEDs. Inside the case is an electronic unit, fuse and terminals for connection of the supply voltage, sensor and load. The temperature sensor is connected to the lower terminal block. If necessary, it is carried out may be extended to any wire 7 m. At the same polarity of the sensor does not matter. To connect the device ART 1 8-16H(ampere), connect the power cord, and the load sensor to the terminal block in accordance with the scheme. Connect as a load of several electric heaters designed for 220V, carried out in parallel (total current and power of the heaters must not exceed the maximum allowed). Scheme for the connection as a load of several electric heaters designed for 12 V, using a power transformer with an output voltage of 12 V. Electric heaters connected in parallel to the secondary winding of the transformer (total current and power of the heaters must not exceed the maximum permissible for the transformer, and to the thermostat). When connecting multiple electric heaters designed for voltages of less than 110V, the connection is made in series (the sum of operating voltages N heaters should be close to 220). Combined, the parallel-serial connection of electric heaters shall be subject to the above limitations in each area, and in general on the load. The temperature sensor is located at the end of the wire, insert Thermometer wells or fix in place the temperature control (control hive).
Set the thermostat to the desired temperature scale and switch, with LED lights Network. If the temperature sensor below the set, after some time the controller switches the load will begin heating and LED "HEAT". Upon reaching the set temperature, the thermostat will automatically turn off the load, and the LED "HEAT" goes out. After lowering the temperature of the load on again and the cycle repeats. All devices are equipped with a system monitoring the temperature sensor.If the sensor is broken or shorted, the unit will turn off and turn on the load indicator "ALARM" (if available). Further work unit will be possible only after its disconnection from the mains and then turn it on. When using thermostats in wet areas or outdoors it is advisable to install them in panels (boxes) with an increased degree of protection (IP), which will prevent condensation inside, water or foreign objects. Keep an eye on the reliability and serviceability of the insulation of power cables and wires sensors. Faulty insulation can cause electric shock and failure of the device. After the first turn on the thermostat a few days to watch him work, if it emits smoke, burning smell, or other overt signs of malfunction switch off the appliance and contact the trading organization. From time to time, especially in the first weeks of operation, check the reliability of fixing power wires and tighten the screws slightly twisted.
Insecure wiring can cause a fire. Do not replace the "bugs" standard fuse or install higher fuse. The item "1xTemp controller and 20xBeehive electric heater 12V 10W, heating hive. Full set" is in sale since Monday, April 11, 2016.
This item is in the category "Business & Industrial\Agriculture & Forestry\Livestock Supplies\Beekeeping". The seller is "kuzlion" and is located in Gulkevichi. This item can be shipped worldwide.