New Electric Full

Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version

Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version
Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version
Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version
Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version
Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version

Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version    Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version

Because of missing regular flights from Russia, pls be informed before making an order. It is a full set with very nice and suitable case. Tester would be always in a safe. It is a professional tool for car alarm workshops and private persons. It works with 12 volts and 24 volts.

Automobile probe tester Pandora ALT-205 is designed for auto electricians and specialists in the installation of security and service devices. This device reflects our understanding of the problems that professional installers each face when working with the most modern cars. The design and circuitry of the Pandora ALT-205 are designed to almost completely eliminate the risk of damage to the vehicles circuits when attempting to diagnose and search for the necessary signal circuits. In Pandora ALT-205, a large number of special software algorithms have been implemented that facilitate the search for specific signals, connection circuits, so necessary when installing security systems and additional equipment. In addition, thanks to the integrated microUSB port, this device has the ability to update software - new firmware with enhanced functionality will be available on the official website. An exclusive gift for installers of modern car alarms - Pandora Pro toolkit.

Pandora Pro set is designed to simplify the work of auto electricians and installation specialists for security and service devices. This kit is simply indispensable for both professionals who install security systems, additional equipment, repair and diagnostics electrics of cars with on-board voltage of 12 and 24 Volts, as well as car owners who are self-repairing and retrofitting their cars.

All tools are packed in a small and very comfortable leather bag-case. All tools are fixed by wired elastic holders, and there are special pockets for cable and consumables required when working with the electrical equipment of the car. Pandora ALT-205 is multifunctional auto electricians device that is designed for professional use in the process of repair and installation work with original electronics of modern cars, including cars with digital data CAN, LIN, K-BUS, W-BUS, K-LINE buses and with data rates up to 1Mbps. The device is designed for modern cars with on-board voltage 12 and 24V.

Measuring of constant voltage up to 30V. Indication of maximum and minimum values, frequency and oscillation period, pulse signals. Recognition of digital bus transmission lines up to 500 kB/s. Switching resistance 50Om and 1kOm, sound and light indication. Micro-USB socket to update the firmware. In order to avoid failure of the device, it is prohibited to measure DC and AC voltages above 36 V. The device is turned on and off by long pressing the button 1 fast on - 2.

Short press the button 1. Short pressing of button 1 turns on the LCD backlight and the illumination of the commutation and measurement zone after 10 seconds. The backlight automatically goes out.

Automatic shutdown of the device will occur after 5 minutes of non-use. Button to switch between modes and submodes. 50 ohm load connect button. Illumination of the measurement zone.

LED parametric measurement indicator, sub-mode indicator. Mode I voltage measurement "VOLT / SENS". Mode II frequency measurement "TAHO / DATA". Mode III measuring pulse duration "PULSE TIMING". Mode IV mode of generating rectangular signals "GENERATOR".

In modes I and II, the inclusion of a load of 50 Ohms, or 1 kOhm in the measurement circuit is available, by. Pressing buttons 3 and 4. Modes are switched by successive short pressing of button 2 MODE. LED indicator 5 displays the selected mode. Hold the MODE button 2 for more than 2 seconds to switch to the submodes menu. Subsequent short presses of the MODE button 2 switch the sub-modes. Submodes are displayed on LCD 10 and LED 9. Designed to measure the voltage level. The voltage value is indicated by the main. 4-digit digital indicator and two additional indicators, averaging the maximum and minimum voltage of the circuit over the last 5 seconds. In this mode, the LED indicator of operation 8, glows green when the voltage.

On a needle less than 1 V, with a voltage on a needle probe from 2 to 6 Volts orange, with a voltage greater than 6 Volts red. LED parametric voltage indicator 9 has five intervals. When the device is closed to ground, a low tone will sound.

During the measurement it is possible to check the voltage change in the circuit by connecting. Load 50 ohms or 1kOhm (buttons 3 and 4). The range of measured voltages is 0.5-36 V with an accuracy of 0.5%. 0.01-0.5 V with an accuracy of 2%.

Starting with the firmware version v. 1.08, the function of holding the connection buttons is available. Load 50 Ohm and 1kOhm (buttons 3 and 4). To enable the holding of buttons 3 or 4 in the pressed state, you need to briefly press the corresponding button twice. Buttons is turned off by repeated short pressing of the 3 or 4 key, or the probe will automatically exit this mode after 60 seconds.

By selecting a sub-mode, you can configure. Audible indication when closing the probe. Tone indication of voltage level. Change of signal tone depending. From the voltage on the needle probe probe.

Light indication when this mode is activated. The voltage level on the needle is displayed. LED indicator 11 with gradation 3-6-9-12 V. Designed to work with the signal circuits of cars with sinusoidal waveform. Or a signal with rectangular pulses, as well as initial recognition of data transmission lines.

Used to search for tachometer impulses, impulse sensor circuits. Designed to measure the duration and polarity of a single pulse. The device allows to measure pulses with duration from 1 ms to 60 seconds, in the voltage range from 0V to 30V. Connect the device to the measured circuit, briefly press the button 3 or 4, while the device will record the current voltage of the circuit and go into the standby mode of the pulse, the screen will appear. When a pulse occurs, the device will record its polarity, duration, and also display. Minimum and maximum values of voltages. In case the pulse duration exceeds 60 seconds. The device will display an error message. Designed to feed a needle-probe probe series of rectangular signals of negative. This mode is used to determine the location of the conductor, simulate the signals of the speed sensors, etc.

4 modes are available in Generator mode. Determining the location of the conductor - when choosing this sub-mode.

A series of triple negative pulses with a pause is fed to the probe needle. The second probe by the presence of such signals is easy to determine the location of the desired. 5Hz - a sub-mode of a square wave signal generator (negative rectangular pulses with a duty cycle of 2) with a frequency of 5 Hertz. 10Hz is a sub-mode of a square wave signal generator with a frequency of 10 Hertz. 15Hz - sub-mode of the signal generator type square wave with a frequency of 15 Hertz.

2, 3 and 4 sub-modes can be useful in simulating signals from speed or speed sensors. For example, when working with the function to disable the standard monitor while the vehicle is moving.

In this mode (including all available sub-modes) the trigger trigger function is available /. Turn off beeps by short pressing buttons 3 or 4. Technical characteristics of the device. Accuracy of voltage measurements 0.5%.

Accuracy of frequency measurement 0.5%. Current consumption in measurement mode 25mA. Current consumption 55mA in backlight mode. Current consumption in the "off" 0.025mA.

The item "Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version" is in sale since Tuesday, May 28, 2019. This item is in the category "eBay Motors\Automotive Tools & Supplies\Diagnostic Service Tools\Electrical Testers, Test Leads". The seller is "diag2car" and is located in Saint Petersburg. This item can be shipped worldwide.

  • Manufacturer Part Number: ALT-205
  • Brand: Pandora

Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version    Car electrical tester Pandora ALT-205 for car alarm masters and etc. Full version