New Electric Full

Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P

Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P
Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P
Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P
Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P
Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P
Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P
Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P

Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P    Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P

Full Set DIY RC Drone Quadrocopter With Gimbal X4M380L Frame Kit with APM2.8 flight control Motor ESC. 11.1V 3300Mah 25C Lipo Battery. 30A Brushless ESC Speed Controller 4. 6M GPS with Compass L5883 25cm Cable1.

5pcs 10cm Servo Receiver Extension Lead Wire Cable1. GPS Folding Antenna Mount Holder1. 3.5mm Bullet Connector 12. 20cm Hook and & Loop Fastening Tape 1. T Plug Male Connector Silicone Wire 1. 11.1V 3300Mah 25C Lipo Battery1. IMAX RC B3 Pro Compact Balance Charger1.

Carbon Fiber Camera Gimbal Mount1. Before you can configure your APM. You will need to first connect everything together.

Show you all the cables. And parts that you will need to connect to your APM. Please note the illustration Below highlights a (TYPICAL) installation. It contains optional equipment including a Camera Gimbal and a Battery Monitor and it utilizes an ESC wired "Y" power connection rather than the power distribution board common to many MultiCopters.

Connecting your motors and RC gear. Overview of connections on the Ardupilot Mega v2 board. The instructions below are for regular RC receivers with PWM output (one cable per channel).

If you're using a "PPM" receiver (one cable carries all channels), follow the instructions. Before you can configure your Arducopter, you will need to first connect everything together. You need to connect your RC receiver to the Input side of the board. You can use the cables included with your Arducopter Kit, or if you are using another frame, you can use jumper cables, or female to female servo cables. Connections between RC receiver and Ardupilot Mega v2 board.

If you are using female to female servo cables. The ground (black) side of each connector must be on the outside for the board, the signal (white/orange) needs to be on the inside as shown below. Connecting with right angle connectors. If you are using a multi-pin connector. That was included with your Arducopter Kit, connect them as shown below.

Input Side for RC reciever. Please note, that your ESC, connectors should be plugged in the the output side, it is suggested that you only use power from one of your ESC's.

This can be dune by cutting the red wire on all but one of the ESC's, or by using a special adaptor. Once again if you are using an Arducopter Kit, with the PDB, then you dont need to worry about this if you soldered everything correctly as the motors are assigned to the correct pins with the cables you plugged connected in the previous step. However you will neet to make sure your motors are spinning in the correct direction. The images below show the possible arducopter configurations with correct motor orientation. Quick Tip: If your motor is not spinning in the correct direction, simply switch the position of any two of the ESC-motor wires.

Arducopter Hexa, Octa, and Y6. Connecting a Roll-Tilt Camera mount. AC2 supports the MaxSonar line of sonars for low level altitude hold and in the future collision avoidance.

Below 10 meters sonar is primarily used for altitude hold. Above 10 meters, the barometric sensor is used. GPS is not required for altitude hold. Connect your Ultrasonic Sensor to the A0 port of your Ardupilot Mega v2 board. The sonar sensors are quite sensitive to noise, adding something like a ferrite choke to your cable could help. The most important is to mount your sonar away from other electronics like ESC, or wireless telemetry modules. Possible Causes of sonar Interferance. Electrical noise caused by ESCs, Servos, or switching BEC's on the same circuit as the Sonar. EMF radiation from motors, motor wires, ESC's or Xbee. Vibration from motors, props, etc. The optical flow sensor is used to improve the position hold accuracy of your arducopter.

This sensor is supported from Arducopter 2.6 and above. Connecting the optical flow sensor to APMv2. Power, GND, NCS pins should be attached to A3. MISO, MOSI and SCLK pins should be directly soldered to the pins shown above.

Default mounting is lens pointing down, pins forward. Its a good idea to secure the wires with some cable ties so they dont break off over time.

How to connect the optical flow sensor to your ardupilot mega board. Make sure the pins are facing forward. Now that everything has been connected everything the next thing to do is configure arducopter firmware for your frame.

Carbon Fiber Camera Gimbal Mount FPV Damping PTZ for DJI Phantom Quadcopter Multicopter Gopro Hero 3. Effective pictures, Product is un-assembly and not include the Camera and DJI Phantom. The item "Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P" is in sale since Monday, December 12, 2016. This item is in the category "Crafts\Needlecrafts & Yarn\Embroidery & Cross Stitch\Hand Embroidery Kits\Cross Stitch Kits". The seller is "wi-model" and is located in Shenzhen.

This item can be shipped worldwide.

  • Gender: Boys
  • Year: 2016
  • Country/Region of Manufacture: China
  • UPC: Does not apply
  • Model: F14893-P
  • MPN: Does not apply
  • Brand: Unbranded/Generic
  • Fuel Source: Electric
  • State of Assembly: Unassembled Kit


Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P    Full Set DIY RC Drone Quadrocopter X4M380L Frame Kit APM 2.8 Gimbal TX F14893-P